Guide

How to Fix a PACS Search That Fails or Returns Nothing

When a PACS search does not give you a list of studies, there are really two different situations: the server answered and found nothing, or the search itself did not work. DICOM Burner tells them apart, so the first job is to read what it is telling you, and the second is to work through the usual causes in order.

This guide assumes DICOM Burner is installed and at least one PACS server has been added.

  1. 1

    Read the line under the search form

    After each search, every PACS you searched gets its own line under the search form. The server name followed by OK and a number of studies means the server answered normally. OK with 0 studies means it found nothing that matched. The server name followed by FAILED and a reason means the search did not complete. One server failing does not stop the others from returning results.

  2. 2

    If it says FAILED with a status code, the PACS rejected the search

    The reason reads that the PACS rejected the query, followed by the status code the server returned and its description. If you had added extra columns, the message also lists the optional columns that were requested, because the server may not support one or more of them. A search is also reported as failed when the PACS ends it without sending a final status, since the results may then be incomplete.

  3. 3

    Click Retry with standard keys only

    After a rejection, a Retry with standard keys only button appears next to Search. It repeats the search as a brand new one that asks the PACS for only the essential fields: patient name, patient ID, accession number, study date, modalities, and Study UID. Stricter servers often accept that. Every other column, including some that are shown by default, stays blank for that search, and the retry never merges with earlier results. If the retry is rejected as well, the button is not offered again, so move on to the next steps. You can also open Choose columns..., remove any columns you added, and search again.

  4. 4

    If it says the query timed out

    A message that the query timed out after 30 seconds with no response means nothing came back from the server, which usually points to an unreachable or unresponsive PACS. Go on to the connection test below. If a PACS goes quiet part-way through a search, the studies it had already sent are listed and the line still reads OK, so if the list looks shorter than you expect, search again.

  5. 5

    Test the connection with a C-ECHO

    Open Settings > PACS Nodes..., select the server, and click Test Connection. DICOM Burner sends a C-ECHO and shows Success with the response time, or Failed with the reason, in the Status column. The test waits about five seconds. A failure here means the problem is the host, the port, a firewall, or the AE titles, not the search itself.

  6. 6

    Check the AE titles

    In the same window, the Called AE Title must be the PACS server's own AE title, and the Calling AE Title is the one that identifies DICOM Burner to the PACS. Many PACS servers only accept connections from calling AE titles that have been registered with them in advance, so if the titles look right, ask your PACS administrator to confirm that yours has been added.

  7. 7

    If it says OK with 0 studies, widen the search

    Clear fields one at a time and search again. Study Date From and Study Date To can be used separately, so leaving To empty searches from a date onward, and leaving From empty searches up to a date. DICOM Burner sends your Patient Name and other text as you typed them, so whether partial names or wildcard characters are accepted depends on your PACS. Searching by Patient ID or Accession # is often the most reliable way to confirm a study exists. A PACS can also limit what a particular calling AE title is allowed to see.

  8. 8

    Remember that a blank column is not a missing study

    If a PACS flags a match as having optional keys it does not support, the study is still listed, and the columns it could not provide are left blank. Hovering over such a cell shows a note that the PACS did not return the attribute.

If a search still fails once the connection test passes and the AE titles are right, use Help > Open Diagnostics Log... to find the details and Help > Contact Support... to ask for help. Include the status code from the FAILED line, because it tells the PACS administrator exactly what the server objected to.

Get DICOM Burner free

Free DICOM burning software for Windows — query PACS, burn to CD/DVD, copy to USB.